Elcometer 106 Pull-Off Adhesion Tester

Elcometer 106 Pull-Off Adhesion Tester is a spray paint or plasma spray on bridge pavement, steel, aluminum, concrete, etc. Allows testing of coatings on it.

Elcometer 106 Pull-Off Adhesion Tester is easy to use and is a fully portable Type II adhesion meter that provides a numerical value for adhesion strength.

  • Supplied with carrying case – ideal for field testing
  • Hand operated – no power supply required
  • Includes cutter for EN13144 and ISO 4624 tests

Description

Elcometer 106 Adhesion Test Method

A test dolly is attached to the coating using an adhesive. The Elcometer 106 adhesion tester has a spring arrangement that applies a buoyant force to the dolly as tension increases.

When the coating is removed from the surface, the indicator on the scale shows the numerical value of the adhesion force expressed in force per unit area required to remove the dolly.

The dolly surface should be examined to detect the fault condition.

A 40mm (1.52″) dolly is available to increase sensitivity at low values or on rough surfaces. When using a 40mm dolly, divide the scale reading by 4.

Elcometer 106 Adhesion Tester – Scale 1

The Elcometer 106 Pull-Off Adhesion Tester Scale 1 is easy to operate and fully portable with an MPa  (N/mm²) of 0.5 – 3.5, a Range of 5 – 35 and a psi of 72 – 500.

  • Part Number : F106—-1
  • Certification : No Certificate
  • Part Number : F106—-1C
  • Certification : Calibration Certificate
Elcometer 106 Adhesion Tester – Scale 2

The Elcometer 106 Pull-Off Adhesion Tester Scale 2 is easy to operate and fully portable with an MPa (N/mm²) of 1 – 7.0, a Range of 10 – 70 and a psi of 145 – 1000.

  • Part Number : F106—-2
  • Certification : No Certificate
  • Part Number : F106—-2C
  • Certification : Calibration Certificate
Elcometer 106 Adhesion Tester – Scale 3

The Elcometer 106 Pull-Off Adhesion Tester Scale 3 is easy to operate and fully portable with an MPa (N/mm²) of 3 – 15, a Range of 30 – 150 and a psi of 435 – 2000.

  • Part Number : F106—-3
  • Certification : No Certificate
  • Part Number : F106—-3C
  • Certification : Calibration Certificate
Elcometer 106 Adhesion Tester – Scale 4

The Elcometer 106 Pull-Off Adhesion Tester Scale 4 is easy to operate and fully portable with an MPa (N/mm²) of 5 – 22, a Range of 50 – 220 and a psi of 725 – 3200.

  • Part Number : F106—-4
  • Certification : No Certificate
  • Part Number : F106—-4C
  • Certification : Calibration Certificate
Elcometer 106 Adhesion Tester – Scale 5

The Elcometer 106 Pull-Off Adhesion Tester Scale 5 is easy to operate and fully portable with an MPa (N/mm²) of 0.05 – 0.2, a Range of 0.5 – 2.0 and a psi of 7.25 – 30.

  • Part Number : F106—-5
  • Certification : No Certificate
  • Part Number : F106—-5C
  • Certification : Calibration Certificate
Range
Part NumberDescriptionMPa (N/mm²)kg/cm²PsiCertificate
F106—-1Elcometer 106 Adhesion Tester – Scale 10.5 – 3.55 – 3572 – 500
       Optional Calibration Certificate available
F106—-2Elcometer 106 Adhesion Tester – Scale 21 – 7.010 – 70145 – 1000
       Optional Calibration Certificate available
F106—-3Elcometer 106 Adhesion Tester – Scale 33 – 1530 – 150435 – 2000
       Optional Calibration Certificate available
F106—-4Elcometer 106 Adhesion Tester – Scale 45 – 2250 – 220725 – 3200
       Optional Calibration Certificate available
F106—-5Elcometer 106 Adhesion Tester – Scale 50.05 – 0.20.5 – 2.07.25 – 30
       Optional Calibration Certificate available
DimensionsScales 1, 2, 5: 175 x 76mm (7 x 3”) Scales 3 and 4: 185 x 76mm (7.5 x 3″)
Dolly Diameter20mm (0.76”)Dolly Area314mm² (0.49sq inch)
Gross weight of KitScale 1, 2 and 5: 2.8kg (6.2lb) Scale 3: 4.2kg (9.3lb) Scale 4: 4.5kg (9.9lb)
Packing ListElcometer 106 Pull-Off Adhesion Tester, pack of 20 dollies, Araldite adhesive, base support ring, magnetic dolly clamp, dolly cutter, carry case and operating instructions.